Propellerhead Reason - 1.0.1 Manual de operaciones descargar pdf (Pagina 191)

MENU AND DIALOG REFERENCE

189

Edit Keyboard Remote

➜ To get an overview of which parameters are remote controllable se-

lect “Edit Keyboard Remote” from the Options menu.

When done, each device you select will show a yellow arrow symbol be-

side every parameter that can be assigned a keyboard remote.

➜ If you click on an assignable parameter, a dialog appears allowing

you to select a key command for that parameter.

You may use any key or a combination of [Shift] + any key.

➜ Simply press the key (or key combination) you wish to use to re-

mote control the parameter.

The “Key Received” field momentarily indicates that it is “learning” the

keystroke(s), and then the dialog displays the name of the key you have

pressed. If [Shift] was used, the box beside the word Shift in the dialog is

ticked.

! Note that the transport panel uses the numeric keypad for various

commands. If you assign a parameter to a single numeric key, the

corresponding transport functionality will be overridden!

About the two Edit Keyboard Remote Modes

If Edit Keyboard Remote is enabled (ticked) on the Options menu, assigned

parameters are “tagged”, showing the remote key for that parameter. In this

mode, however, you cannot operate Reason normally, as every parameter

you click on will open the Key Remote dialog. This mode is primarily for over-

view of available parameters and the current assignments.

➜ Another way to assign keyboard remote commands is to have “Edit

Keyboard Remote” deselected on the Options menu, and to simply

[Ctrl]-click (Mac) / right-click (Windows) the parameter you wish to

remote control.

This opens a pop-up menu, where one of the options will be “Edit Key-

board Remote”. Selecting this opens the Key Remote dialog. Thus, you

do not have to enable/disable Edit mode from the Options menu if you

know that a parameter is assignable.

! If you try to assign a Remote Key that is already in use, you will get

an alert asking if you wish to change the current assignment.

Clear All Keyboard Remote

This menu command removes all keyboard mapping you have set up for the

song.

Enable MIDI Remote Mapping

When this is activated, MIDI messages can be used to control devices, as

set up with the Edit MIDI Remote feature.

Edit MIDI Remote Mapping

1. To get an overview of which parameters are MIDI remote controlla-

ble select “Edit MIDI Remote Mapping” from the Options menu.

When done, each device you select will show a green arrow symbol be-

side every parameter that can be assigned a MIDI remote.

2. If you click on a assignable parameter, a dialog appears allowing

you to select a MIDI controller (or a Note number) to control that pa-

rameter.

Note numbers function exactly like Keyboard remote - they can only con-

trol on/off or min/max values.

3. Make sure that the “Learn from MIDI Input” box is ticked.

4. Simply turn the knob (or slider etc.) that you wish to use to remote

control the parameter.

The “MIDI Received” field momentarily flickers as you turn the knob, and

then the dialog shows the controller number and the channel it is trans-

mitted on.

5. Click “OK” to exit the dialog.

The selected parameter now has a tag, displaying the controller number,

and the MIDI channel used.

6. To exit Edit MIDI Remote Mapping mode, deselect it from the Op-

tions menu.

You do not always have to use this method - see below.

About the two Edit MIDI Remote Mapping Modes

If Edit MIDI Remote Mapping is enabled (ticked) on the Options menu, as-

signed parameters are “tagged”, and the arrow indicators show the assign-

able parameters. In this mode, however, you cannot operate Reason

normally, as every parameter you click on will open the MIDI Remote dialog.

The Edit mode is primarily for overview of available parameters and the cur-

rent assignments.

➜ Another way to assign keyboard remote commands is to have “Edit

MIDI Remote Mapping” deselected on the Options menu, and to

simply [Ctrl]-click (Mac) / right-click (Windows) the parameter you

wish to remote control.

This opens a pop-up menu, where one of the options will be “Edit MIDI

Remote Mapping”. Selecting this opens the MIDI Remote dialog. Thus,

you do not have to select Edit mode from the Options menu if you already

know that a parameter is free and assignable.

1 2 ... 186 187 188 189 190 191 192 193 194 195 196 ... 206 207

Propellerhead Reason - 1.0.1 Manual de operaciones Pagina 191

Comentarios a estos manuales

Propellerhead Reason - 1.0.1 Manual de operaciones Pagina 191

Comentarios a estos manuales

Relacionado con productos y manuales para Software Propellerhead Reason - 1.0.1