Propellerhead Reason - 1.0.1 Manual de operaciones descargar pdf (Pagina 133)

NN-19 DIGITAL SAMPLER

131

Retrig

This is the “normal” setting for playing polyphonic patches. That is, when you

press a key without releasing the previous, the envelopes are retriggered,

like when you release all keys and then press a new one. In monophonic

mode, Retrig has an additional function; if you press a key, hold it, press a

new key and then release that, the first note is also retriggered.

Portamento (Time)

Portamento is when the pitch “glides” between the notes you play, instead of

instantly changing the pitch. The Portamento knob is used to set how long it

takes for the pitch to glide from one pitch to the next. If you don’t want any

Portamento at all, set this knob to zero.

Setting Number of Voices - Polyphony

This determines the polyphony, i.e. the number of voices a patch can play si-

multaneously. This can be used to make a patch monophonic (=a setting of

“1”), or to extend the number of voices available for a patch. The maximum

number of voices you can set a patch to use is 99.

! Note that the Polyphony setting does not “hog” voices. For exam-

ple, if you have a patch that has a polyphony setting of ten voices,

but the part the patch plays only uses four voices, this won’t mean

that you are “wasting” six voices. In other words, the polyphony

setting is not something you need to consider if you want to con-

serve CPU power - it is only the number of voices actually used that

counts.

Voice Spread

This parameter can be used to control the stereo (pan) position of voices.

The Spread knob determines the intensity of the panning. If this is set to “0”,

no panning will take place. The following pan modes can be selected:

Low Bandwidth

This will remove some high frequency content from the sound, but often this

is not noticeable (this is especially true if you have “filtered down” your loop).

Activating this mode will save you some extra computer power, if needed.

Controller Section

NN-19 can receive common MIDI controller messages, and route these to

various parameters. The following MIDI messages can be received:

• Aftertouch (Channel Pressure)

• Expression Pedal

• Breath Control

If your MIDI keyboard is capable of sending Aftertouch messages, or if you

have access to an Expression Pedal or a Breath controller, you can use

these to modulate NN-19 parameters. The “Source” selector switch deter-

mines which of these message-types should be received.

These messages can then be assigned to control the following parameters:

Mode

Description

Key This will shift the pan position gradually from left to right the higher

up on the keyboard you play.

Key 2 This will shift the pan position from left to right in 8 steps (1/2 oc-

tave) for each consecutive higher note you play, and then repeat

the cycle.

Jump This will alternate the pan position from left to right for each note

played.

F. Freq This sets external modulation control of the filter frequency pa-

rameter. A positive value will increase the frequency with higher

external modulation values. Negative values invert this relation-

ship.

LFO 1 This sets external modulation control of the LFO Amount param-

eter. A positive value will increase the LFO amount with higher

external modulation values. Negative values invert this relation-

ship.

Amp This let’s you control the overall volume of the sound with exter-

nal modulation. If a positive value is set, the volume will increase

with higher external modulation values. A negative value inverts

this relationship.

1 2 ... 128 129 130 131 132 133 134 135 136 137 138 ... 206 207

Propellerhead Reason - 1.0.1 Manual de operaciones Pagina 133

Comentarios a estos manuales

Propellerhead Reason - 1.0.1 Manual de operaciones Pagina 133

Comentarios a estos manuales

Relacionado con productos y manuales para Software Propellerhead Reason - 1.0.1